International Standards and Conformity Assessment for all electrical, electronic and related technologies

SC 86B

Fibre optic interconnecting devices and passive components

 

Detail

Committee
Working Groups
Project Leader

Current

Status

Frcst Pub

Date

Stability

Date

SC 86BWG 4 Mr. Matthew BrownPPUB2015-062021

History

Stage
Document
Downloads
Decision Date
Target Date
AMW
86B/3086/RR PDF file 20 kB
2010-08-132010-08
1CD
86B/3087/CD PDF file 2152 kB
2010-08-132010-08
CDM
86B/3135/CC Word file 126 kB
PDF file 625 kB
2010-12-032010-12
A2CD
86B/3135A/CC Word file 126 kB
PDF file 192 kB
2012-02-152011-05
2CD
86B/3477/CD PDF file 592 kB
2012-07-132012-08
CDM
86B/3523/CC Word file 174 kB
PDF file 178 kB
2012-09-282012-10
A3CD
86B/3523A/CC Word file 191 kB
PDF file 187 kB
2013-01-252012-12
3CD
86B/3630/CD PDF file 1445 kB
2013-05-102013-01
CDM
86B/3677/CC Word file 293 kB
PDF file 144 kB
2013-08-302013-12
ACDV
86B/3677A/CC Word file 298 kB
PDF file 201 kB
2014-01-10 
CCDV
86B/3725/CDV
PDF file 596 kB
PDF file 1181 kB
2014-03-212014-01
AFDIS
86B/3833/RVC Word file 316 kB
PDF file 171 kB
2014-09-192014-09
DECFDIS
2015-01-192015-01
RFDIS
2015-02-022015-02
CFDIS
86B/3886/FDIS

2015-03-132015-04
APUB
86B/3912/RVD PDF file 150 kB
2015-05-192015-05
BPUB
2015-05-202015-05
PPUB
2015-06-252015-06
 2018-12

Abstract

IEC 61300-3-35:2015 is available as IEC 61300-3-35:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61300-3-35:2015 describes methods for quantitatively assessing the end face quality of a polished fibre optic connector or of a fibre optic transceiver using a fibre-stub type interface. Sub-surface cracks and fractures are not considered in this standard. In general, the methods described in this standard apply to 125 μ cladding fibres contained within a ferrule and intended for use with sources of ≤ 2 W of input power. However, portions are applicable to non-ferruled connectors and other fibre types. Those portions are identified where appropriate. It is not the intention of this standard that the size of scratches should be measured, the dimensions and requirements are selected such that they can be estimated. There is no need to measure for example if a scratch is 2,3 μm wide. This second edition cancels and replaces the first edition published in 2009 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- modification to the title;
- addition of some terms and definitions;
- reconsideration of the specific values of Tables 1 to 4 to reflect the current market situation;
- addition of visual requirements for single-mode transceivers using a fibre-stub interface in Table 3;
- addition of a sentence in 4.1 concerning the susceptibility of the methods to system variability. Keywords: end face quality of a polished fibre optic connector, fibre optic transceiver using a fibre-stub type interface

Project

IEC 61300-3-35:2015 ED2

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers

 

 

Associated Documents:

86B/4159/RR

PDF file 92 kB
86B/4068/RQ

PDF file 173 kB
86B/4055/Q

Word file 33 kB
86B/3868A/RM

PDF file 490 kB
SMB/5256/DL

PDF file 186 kB
SMB/4976/DL

PDF file 344 kB
SMB/4747/DL

PDF file 233 kB