SC 48D

Additional adjustable pitch-hole in IEC 60297: Defined mounting structures (racks)

Connector dependent interface dimensions for subracks and plug-in units

IEC 61587-X Ed.1.0: Mechanical structures for electronic equipment - Part X: Interface dimensions for cooling devices in cabinets

IEC 60297-3-xxx/Ed1: Mechanical structures for electronic equipment - dimensions of mechanical structures of the 482,6mm (19in) series - Part xxx: Universal base grid for small form factor chassis

Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 1: Panels and racks

Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 2: Cabinets and pitches of rack structures

Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 3: Subracks and associated plug-in units

Amendment 1 - Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 3: Subracks and associated plug-in units

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-102: Injector/extractor handle

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-102: Injector/extractor handle

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-103: Keying and alignment pin

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-104: Connector dependent interface dimensions of subracks and plug-in units

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-105: Dimensions and design aspects for 1U high chassis

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-107: Dimensions of subracks and plug-in units, small form factor

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-108: Dimensions of R-type subracks and plug-in units

Mechanical structures for electrical and electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-109: Dimensions of chassis for embedded computing devices

Mechanical structures for electrical and electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-110: Residential racks and cabinets for smart houses

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions

Amendment 1 - Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-101: Subracks and associated plug-in units - Injector/extractor handle

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-102: Subracks and associated plug-in units - Electromagnetic shielding provision

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-104: Subracks and associated plug-in units - Keying

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-105: Subracks and associated plug-in units - Alignment and/or earth pin

Plug-in unit/subrack grounding for subracks and associated plug-in units with extended features added to IEC 60297-3 and IEC 60297-4

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units

Restructuring of IEC 60297-3, 60297-4 and 48D/119/CD (possible IEC 60297-5) into a sectional and detail standard

Restructuring of IEC 60297-3, 60297-4 and 48D/119/CD (possible IEC 60297-5) into sectional and detail standards

Systematic review of IEC 916 (1988)

Mechanical structures for electronic equipment - Terminology

Systematic review of IEC 917-0 (1989)

Modular order for the development of mechanical structures for electronic equipment practices - Part 0: Guide for the users of IEC 917

Modular order for the development of mechanical structures for electronic equipment practices

Amendment 1 - Modular order for the development of mechanical structures for electronic equipment practices

Modular order for the development of mechanical structures for electrical and electronic equipment practices - Part 1: Generic standard

Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard

Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard

Amendment 1 - Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard

Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice

Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 1: Detail specification - Dimensions for cabinets and racks

Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 2: Detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-3: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Extended detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-3: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Extended detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in)

Modular order for the development of mechanical structures for electronic equipment practices - Part 2-5: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Cabinet interface dimensions for miscellaneous equipment

Mechanical structures for electrical and electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor conditions

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 1: Climatic, mechanical tests and safety aspects for cabinets, racks, subracks and chassis

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 1: Climatic, mechanical tests and safety aspects for cabinets, racks, subracks and chassis

Mechanical structures for electronic equipment - Tests for IEC 60917 and 60297 - Part 2: Seismic tests for cabinets and racks

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 2: Seismic tests for cabinets and racks

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 4: Combination of performance levels for modular cabinets

Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 5: Seismic tests for chassis, subracks and plug-in units

Mechanical structures for electrical and electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 6: Security aspects for indoor cabinets

Mechanical structures for electrical and electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 6: Security aspects for indoor cabinets

Mechanical structures for electrical and electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 6: Security aspects for indoor cabinets

Mechanical structures for electrical and electronic equipment - Outdoor enclosures - Part 1: Design guidelines

Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines

Mechanical structures for electronic equipment - Outdoor enclosures - Part 1: Design guidelines

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2: Coordination dimensions

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2: Sectional specification - Coordination dimensions for cases and cabinets

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2-1: Detail specification - Dimensions for cabinets

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2-1: Detail specification - Dimensions for cabinets

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2-2: Detail specification - Dimensions for cases

Mechanical structures for electronic equipment - Outdoor enclosures - Part 2-2: Detail specification - Dimensions for cases

Mechanical structures for electrical and electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects

Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects

Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Sectional specification - Climatic, mechanical tests and safety aspects for cabinets and cases

Method of evaluating the thermal performance of enclosures

Mechanical structures for electronic equipment - Design guide: Interface dimensions and provisions for water cooling of electronic equipment within cabinets of the IEC 60297 and IEC 60917 series

Mechanical structures for electronic equipment - Thermal management for cabinets in accordance wit IEC 60297 and IEC 60917 series - Part 1: Design guide: Interface dimension and provision for thermoelectrical cooling systems (Peltier effect)

Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 2: Method for the determination of forced air cooling

Mechanical structures for electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 2: Design guide: Method for determination of forced air-cooling structure

Mechanical structures for electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 3: Design guide: Evaluation method for thermoelectrical cooling systems (Peltier effect)

Mechanical structures for electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 4: Cooling performance tests for water supplied heat exchangers in electronic cabinets

Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 5: Cooling performance evaluation for indoor cabinets

Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 series - Part 6: Air recirculation and bypass of indoor cabinets

Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with IEC 60297 and IEC 60917 Series - Part 6: Air recirculation and bypass of indoor cabinets

Mechanical structures for electronic equipment-Safety requirements for mechanical lock

Mechanical structures for electrical and electronic equipment - Aisle containment for IT cabinets - Part 1: Dimensions and mechanical requirements

Mechanical structures for electrical and electronic equipment - Aisle containment for IT cabinets - Part 2: Details of air flow, air separation and air cooling requirements

Mechanical structures for electrical and electronic equipment - Aisle containment for IT cabinets - Part 3: Aspects of operational and personal safety